flinter

Vielen Dank, das hatte ich übersehen. Ursprünglich, alles mit 42.2 war er auch installiert. Durch den Wechsel auf die frühere Version, ist er mir entwischt. Leider ohne Erfolg. clara:~ # zypper se -si pcsc Loading repository data... Reading installed packages... S | Name | Type | Version | Arch | Repository --+----------------+---------+-----------------------+--------+------------------- i | libpcsclite1 | package | 1.8.14-1.1 | x86_64 | openSUSE:Leap:42.1 i | pcsc-ccid | package | 1.4.20-4.2 | x86_64 | openSUSE:Leap:42.1 i | pcsc-cyberjack | package | 3.99.5final.SP09-79.1 | x86_64 | security:chipcard i | pcsc-lite | package | 1.8.14-1.1 | x86_64 | openSUSE:Leap:42.1 Bei mir nutzt keine Linuxanwendung den Leser, er muss über virtuelbox an einen w7-Gast weitergeleitet werden. Theoretisch kann da auch was anderes sein. Ich orientiere mich aber an die Fehlermeldungen beim usb-Anschließen und dass die led, die normalerweise an ist nur kurz aufblinkt und dann aus ist. Jan 19 14:42:59 clara systemd[1]: Started PC/SC Smart Card Daemon. Jan 19 14:43:44 clara kernel: usb 6-3: USB disconnect, device number 5 Jan 19 14:43:44 clara kernel: cyberjack ttyUSB0: Reiner SCT Cyberjack USB card reader converter now disconnected from ttyUSB0 Jan 19 14:43:44 clara kernel: cyberjack 6-3:1.0: device disconnected Jan 19 14:43:44 clara systemd[1]: smartcard.target: Unit not needed anymore. Stopping. Jan 19 14:43:44 clara systemd[1]: Stopped target Smart Card. Jan 19 14:43:51 clara kernel: usb 6-3: new full-speed USB device number 6 using ohci-pci Jan 19 14:43:51 clara kernel: usb 6-3: New USB device found, idVendor=0c4b, idProduct=0100 Jan 19 14:43:51 clara kernel: usb 6-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0 Jan 19 14:43:51 clara kernel: cyberjack 6-3:1.0: Reiner SCT Cyberjack USB card reader converter detected Jan 19 14:43:51 clara kernel: usb 6-3: Reiner SCT Cyberjack USB card reader converter now attached to ttyUSB0 Jan 19 14:43:51 clara mtp-probe[6503]: checking bus 6, device 6: "/sys/devices/pci0000:00/0000:00:12.0/usb6/6-3" Jan 19 14:43:52 clara mtp-probe[6503]: bus: 6, device: 6 was not an MTP device Jan 19 14:43:52 clara systemd[1]: Reached target Smart Card. Jan 19 14:43:53 clara ModemManager[1193]: <warn> (ttyUSB0): port attributes not fully set Jan 19 14:43:56 clara ModemManager[1193]: <warn> (ttyUSB0): port attributes not fully set Jan 19 14:43:59 clara ModemManager[1193]: <warn> (ttyUSB0): port attributes not fully set Jan 19 14:44:05 clara ModemManager[1193]: <warn> (ttyUSB0): port attributes not fully set Jan 19 14:44:08 clara ModemManager[1193]: <warn> (ttyUSB0): port attributes not fully set Jan 19 14:44:08 clara kernel: device eth0 left promiscuous mode Jan 19 14:44:11 clara ModemManager[1193]: <info> Couldn't find support for device at '/sys/devices/pci0000:00/0000:00:12.0/usb6/6-3': not supported by any plugin Mit dem pcsc-cyberjack sind nun auch die udev-regeln da. Allerdings verstehe ich davon nichts. clara:~ # cat /usr/lib/udev/rules.d/40-cyberjack.rules SUBSYSTEM!="usb", GOTO="cyberjack_rules_end" ENV{DEVTYPE}!="usb_device", GOTO="cyberjack_rules_end" ACTION!="add", GOTO="cyberjack_rules_end" ENV{ID_USB_INTERFACES}=="", IMPORT{program}="usb_id --export %p" ATTRS{idVendor}=="0c4b", ATTRS{idProduct}=="0100", ENV{ID_SMARTCARD_READER}="1" ATTRS{idVendor}=="0c4b", ATTRS{idProduct}=="0300", ENV{ID_SMARTCARD_READER}="1" ATTRS{idVendor}=="0c4b", ATTRS{idProduct}=="0400", ENV{ID_SMARTCARD_READER}="1" ATTRS{idVendor}=="0c4b", ATTRS{idProduct}=="0401", ENV{ID_SMARTCARD_READER}="1" ATTRS{idVendor}=="0c4b", ATTRS{idProduct}=="0500", ENV{ID_SMARTCARD_READER}="1" ATTRS{idVendor}=="0c4b", ATTRS{idProduct}=="0501", ENV{ID_SMARTCARD_READER}="1" LABEL="cyberjack_rules_end" Mir gehen die Ideen aus, was ich noch machen kann.

Auch ich kann nach der Umstellung von 42.1 auf 42.2 nicht mehr auf den Chipkartenleser zugreifen. Allerdings habe ich eine andere Umgebung und andere Meldungen. clara:~ # systemctl status pcscd.service â— pcscd.service - PC/SC Smart Card Daemon Loaded: loaded (/usr/lib/systemd/system/pcscd.service; indirect; vendor preset: enabled) Active: active (running) since Thu 2017-01-19 09:37:22 CET; 14s ago Main PID: 3066 (pcscd) Tasks: 2 (limit: 512) CGroup: /system.slice/pcscd.service └─3066 /usr/sbin/pcscd --foreground --auto-exit Jan 19 09:37:22 clara systemd[1]: Started PC/SC Smart Card Daemon. clara:~ # lsusb Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 007 Device 002: ID 046d:c00e Logitech, Inc. M-BJ58/M-BJ69 Optical Wheel Mouse Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 006 Device 003: ID 046a:0023 Cherry GmbH CyMotion Master Linux Keyboard G230 Bus 006 Device 002: ID 0c4b:0100 Reiner SCT Kartensysteme GmbH cyberJack e-com/pinpad Wenn ich den Chipkartenleser anschließe kommen die Meldungen: lara:~ # systemctl status pcscd.service â— pcscd.service - PC/SC Smart Card Daemon Loaded: loaded (/usr/lib/systemd/system/pcscd.service; indirect; vendor preset: enabled) Active: active (running) since Thu 2017-01-19 09:37:22 CET; 14s ago Main PID: 3066 (pcscd) Tasks: 2 (limit: 512) CGroup: /system.slice/pcscd.service └─3066 /usr/sbin/pcscd --foreground --auto-exit Jan 19 09:53:51 clara nmbd[1857]: Cannot sync browser lists. Jan 19 09:57:30 clara kernel: usb 6-3: USB disconnect, device number 2 Jan 19 09:57:30 clara kernel: cyberjack ttyUSB0: Reiner SCT Cyberjack USB card reader converter now disconnected from ttyUSB0 Jan 19 09:57:30 clara kernel: cyberjack 6-3:1.0: device disconnected Jan 19 09:57:40 clara kernel: usb 6-3: new full-speed USB device number 4 using ohci-pci Jan 19 09:57:40 clara kernel: usb 6-3: New USB device found, idVendor=0c4b, idProduct=0100 Jan 19 09:57:40 clara kernel: usb 6-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0 Jan 19 09:57:40 clara kernel: cyberjack 6-3:1.0: Reiner SCT Cyberjack USB card reader converter detected Jan 19 09:57:40 clara kernel: usb 6-3: Reiner SCT Cyberjack USB card reader converter now attached to ttyUSB0 Jan 19 09:57:40 clara mtp-probe[3220]: checking bus 6, device 4: "/sys/devices/pci0000:00/0000:00:12.0/usb6/6-3" Jan 19 09:57:41 clara mtp-probe[3220]: bus: 6, device: 4 was not an MTP device Jan 19 09:57:43 clara ModemManager[1193]: <warn> (ttyUSB0): port attributes not fully set Jan 19 09:57:46 clara ModemManager[1193]: <warn> (ttyUSB0): port attributes not fully set Jan 19 09:57:49 clara ModemManager[1193]: <warn> (ttyUSB0): port attributes not fully set Jan 19 09:57:55 clara ModemManager[1193]: <warn> (ttyUSB0): port attributes not fully set Jan 19 09:57:58 clara ModemManager[1193]: <warn> (ttyUSB0): port attributes not fully set Jan 19 09:58:01 clara ModemManager[1193]: <info> Couldn't find support for device at '/sys/devices/pci0000:00/0000:00:12.0/usb6/6-3': not supported by any plugin Da bei mir auch beim Einstecken kurz beide Leds aufleuchten und dann ausgehen, habe ich nach dem Vorschlag (https://forums.opensuse.org/showthread.php/521462-HBCI-Kartenleser-f%C3%BCr-Hibiscus/page3) die 42.1 Module eingebunden. Allerdings ohne Erfolg. Die MOdule: clara:~ # zypper se -si pcsc chip Retrieving repository 'Packman Repository' metadata ....................................................................................................................[done] Building repository 'Packman Repository' cache .........................................................................................................................[done] Loading repository data... Reading installed packages... S | Name | Type | Version | Arch | Repository --+--------------+---------+------------+--------+------------------- i | libchipcard | package | 5.0.4-34.2 | x86_64 | security:chipcard i | libchipcard6 | package | 5.0.4-34.2 | x86_64 | security:chipcard i | libpcsclite1 | package | 1.8.14-1.1 | x86_64 | openSUSE:Leap:42.1 i | pcsc-ccid | package | 1.4.20-4.2 | x86_64 | openSUSE:Leap:42.1 i | pcsc-lite | package | 1.8.14-1.1 | x86_64 | openSUSE:Leap:42.1 Ich kann keine cyberjack.rules finden. Wer kann mir weiterhelfen? Vielen Dank Franz